PM2 Series
EMI / RFI Filters
IEC-320 C14 Power Entry Module
1-6 Amp Hgh Performance EMI Line Filters
Specifications
| Voltage rating: | 115/250 VAC |
| Line frequency: | 50/60 Hz |
| Leakage current (line to ground): | 0.25 mA maximum at 115 V, 60 Hz 0.50 mA maximum at 250 V, 50 Hz |
| Test Voltage: | Line to ground, 2250 VDC Line to line, 1450 VDC |
Applications
SAE Power’s high performance filtered power modules provide he convenience of single-point, snap-in mounting of an IEC connector, a fuse holder with optional power ON/OFF switch and voltage selector switch plus an EMI filter. These two-stage filters are ideal for applications in which greater low frequency attenuation is desired. For dual fuse, consult factory.
Certifications
UL File No. E62459, CSA File No. LR56661, TUV File No. R72070222.
Electrical Schematics
Figure A
Figure B
Figure C
Performance
| Current Rating | Type | Frequency, MHz | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Common Mode | 0.01 | 0.05 | 0.1 | 0.15 | 0.50 | 1 | 5 | 10 | 30 | |
| All | 5 | 14 | 20 | 31 | 56 | 62 | 60 | 50 | 35 (db) | |
| Differential Mode | ||||||||||
| All | 0.5 | 7 | 10 | 9 | 25 | 65 | 60 | 50 | 45 (db) | |
Minimum Insertion loss in 50 ohm system per MIL-STD-220A.
Ordering Information
| Part Number | Rated Current | Rated Current | Power Switch | Voltage Selector | Schematic Type |
|---|---|---|---|---|---|
| 115 VAC Operation | 250 VAC Operation | ||||
| PM2A6 | 6A | 6A | - | - | A |
| PM2B6 | 6A | 6A | Single Pole1 | - | A |
| PM2C6 | 6A | 4A | Dual Pole2 | - | B |
| PM2D6 | 6A | 5A | Single Pole1 | Rear3 | A |
| PM2E6 | 6A | 4A | Dual Pole2 | Rear3 | B |
| PM2F6 | 6A | 5A | - | Rear3 | A |
| PM2G6 | 6A | 6A | - | Front4 | C |
Notes:
1. Single Pole Switch is UL & CSA Approved for 6 Amps @ 125 VAC / 250 VAC, VDE Approved for 6 Amps @ 250 VAC. Max inrush current of 24 Amps.
2. Dual Pole Switch is UL & CSA Approved for 6 Amps @ 125 VAC / 4 Amps @ 250 VAC, VDE Approved for 4 Amps @ 250 VAC. Max inrush current of 51 Amps.
3. Voltage Selector is UL, CSA & VDE Approved for 10 Amps @ 125 VAC and 5 Amps @ 250 VAC.
4. Voltage Selector is UL & CSA Approved for 6A @ both 125 VAC / 250 VAC, VDE Approved for 6 Amps @ 250 VAC.
Case Styles
PM2A6
PM2B6 / PM2C6 (switch marking reversed)
PM2D6
PM2G6
PANEL CUT-OUT
Specifications subject to change.